Search Results - aussiefrogs - The Australian French Car Forum Since 1999
  • Register
  • Help

Search:

Type: Posts; User: Wintermute; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    18
    Views
    524

    Have you checked the fault codes? I've had a...

    Have you checked the fault codes? I've had a high RPM Miss (probably closer to 6000RPM) in My S16 which was a dodgy O2 sensor, I think an intermittent connection of one of the wires at the actual...
  2. Replies
    53
    Views
    4,921

    I run these in my S16. First set of dba slotted...

    I run these in my S16. First set of dba slotted lasted me 10 years (every other disk I ever had before that lasted max 18 months. This set I've had a bit over a year. ...
  3. Replies
    2
    Views
    180

    Thanks lowpugV2 :)

    Thanks lowpugV2 :)
  4. Replies
    2
    Views
    180

    306 top engine mount repair (Sydney)

    Hi looking for recommendation on someone to weld up the body where the top engine mount screws in. Mine has completely broken the piece out.

    Paul Vassello used to do them but he doesn't have a...
  5. Replies
    27
    Views
    1,097

    I've never driven a six so I don't know the...

    I've never driven a six so I don't know the difference performance wise, but personally I much prefer the styling of the S16. There is something more menacing and raw about it. The six is a bit too...
  6. Replies
    27
    Views
    1,097

    The S16 should come in before the gti6 ;) Only...

    The S16 should come in before the gti6 ;) Only roughly 300 S16's were sold in Aus, I'd guess that the 6's would have been a few more, but maybe not a lot more. The number of either S16's or GTi6's...
  7. Replies
    747
    Views
    82,637

    It's a nice day. Will pop in about 12:30 if...

    It's a nice day. Will pop in about 12:30 if anyone is still around and can show off my new big red button :wink2:

    Tony.
  8. Replies
    747
    Views
    82,637

    Oh it's that day again!! thanks for the tip!! ...

    Oh it's that day again!! thanks for the tip!!

    Tony.
  9. Replies
    747
    Views
    82,637

    Missed another one!! Perhaps next month :)

    Missed another one!! Perhaps next month :)
  10. The original manifold uses a long branch for revs...

    The original manifold uses a long branch for revs under 4000RPM, this increases the low end torque. The RS also has a different head and exhaust manifold, so you may find that this is just the...
  11. Replies
    10
    Views
    1,885

    I had the same problem many years ago. It was...

    I had the same problem many years ago. It was the zenner (fails short circuit and is wired (reverse) from positive to negative. As mentioned it protects against voltage spikes.

    The original is...
  12. Replies
    2,413
    Views
    308,923

    This morning turning onto Hill road off Paramatta...

    This morning turning onto Hill road off Paramatta rd. A red Peugeot 3008 Police car! It had some stylized word on the drivers door as well which I didn't catch. It appeared to have highway patrol...
  13. Replies
    38
    Views
    6,682

    Sticky: I wasn't able to attend either as I was attending...

    I wasn't able to attend either as I was attending a 90th Birthday party. I drove over the Silverwater bridge a bit before 11:00AM and it looked like it was a good turn out!

    Tony.
  14. Replies
    747
    Views
    82,637

    Sorry I should have posted that I was going to...

    Sorry I should have posted that I was going to come. Got the message at 10:00AM that the washer was ready to pick up and thought It'd only take me an hour and I'd be there by 11:00AM. based on the...
  15. Replies
    747
    Views
    82,637

    I suspect no one else will be arriving so I'll...

    I suspect no one else will be arriving so I'll head home.
  16. Replies
    747
    Views
    82,637

    Bugger just missed you. If i didn't stop for...

    Bugger just missed you. If i didn't stop for petrol would have caught you.

    Went to bankstown to pick up a pressure washer. On special at super cheap this weekend.

    Tony.
  17. Replies
    747
    Views
    82,637

    Thanks KB :)

    Thanks KB :)
  18. Replies
    747
    Views
    82,637

    No Notice this month? is Bigrr ok? Assuming...

    No Notice this month? is Bigrr ok? Assuming tomorrow is the day, though I am uncertain I will be able to attend, as the wife mentioned possibly doing something Sunday.

    Tony.
  19. Replies
    747
    Views
    82,637

    We were. I left around 1:00PM I think... ...

    We were. I left around 1:00PM I think...

    Some pics :)
  20. Replies
    747
    Views
    82,637

    I remembered at about 1:30PM, by which time I had...

    I remembered at about 1:30PM, by which time I had other things I had to do. Looks like I missed a good day!

    Tony.
  21. Replies
    22
    Views
    984

    I got mine when the airbox got wrecked hitting a...

    I got mine when the airbox got wrecked hitting a tall curb on Mt Victoria (diesel spill on the road)... 12 week wait for the new airbox, so got the pod as a temp fix.... I never put the new airbox...
  22. Replies
    22
    Views
    984

    No probs. WIll be interested to see what you...

    No probs. WIll be interested to see what you come up with :)

    Its been something I've thought about but not done anything (except the original buscuit tin).

    Tony.
  23. Replies
    4
    Views
    499

    Ah that's right. It is in a pig of a place. ...

    Ah that's right. It is in a pig of a place. Not easy to get to at all. Horrible job replacing it. I think I had blocked that memory out!

    Tony.
  24. Replies
    4
    Views
    499

    Sorry dup.

    Sorry dup.
  25. Replies
    4
    Views
    499

    yikes!! That plastic bit is pretty hefty, Have...

    yikes!! That plastic bit is pretty hefty, Have you lost the heat shield off the manifold? I'm trying to remember exactly what the plastic bung looks like, I think from memory it has a skirt...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4