Search Results - aussiefrogs - The Australian French Car Forum Since 1999
  • Register
  • Help

Search:

Type: Posts; User: James504; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    7
    Views
    351

    I'd take a single.

    I'd take a single.
  2. WTB: s1 405 glovebox+lid and A/c control box

    Hey all,

    After a s1 405 glove box lid+ inner in grey and good condition. Also a S1 Ac/temp control unit with working vent selection.

    Cheers, James.
  3. Usually, yes. A good number of 9hz's would come...

    Usually, yes. A good number of 9hz's would come in looking like that.
  4. The turbine to fap v-band clamp always leak. They...

    The turbine to fap v-band clamp always leak. They were superseded to a newer part.
  5. Replies
    13
    Views
    285

    Deactivate rds, then re-save the station to your...

    Deactivate rds, then re-save the station to your desired preset.
  6. Replies
    26
    Views
    1,106

    Also worked out why the K light didn't work. ...

    Also worked out why the K light didn't work.

    54426

    They were very tight, looks like tension stress. I removed the pins from the 55way connector and soldered a lengthened join. My wiring diagram...
  7. Replies
    26
    Views
    1,106

    Towbar fitted! Finally got round to it. Picked...

    Towbar fitted! Finally got round to it. Picked this up from a fellow frogger down in Ballina...well worth the drive, beautiful part of the world. Wire brushed the bar and sprayed with killrust from...
  8. Replies
    26
    Views
    1,106

    Yeah t16 wheels are in the too hard basket. The...

    Yeah t16 wheels are in the too hard basket. The gti180 wheels really suit the car in my eyes. I'd only ever swap them for a set of these.
    ...
  9. Replies
    26
    Views
    1,106

    54186 Finally got around to installing the...

    54186

    Finally got around to installing the eibach front springs. Strut tops were knackered also. I've also used S2 strut top rubbers which are about 5mm higher uncompressed when installed. I May...
  10. Replies
    15
    Views
    349

    Finally had enough with the tensioner squeel when...

    Finally had enough with the tensioner squeel when cold. I had a search around the shed and found a few pulleys to try. Had it set in my mind that I was going to use a es9j4 timing belt tensioner. So...
  11. Like I said earlier it is possible to peg the...

    Like I said earlier it is possible to peg the exhaust cam in an incorrect position. Refer to picture.
    53446

    'A' is the correct position, '1' is the incorrect. This gives low compression and...
  12. Replies
    14
    Views
    331

    Having picked my towbar up on sunday. It looks...

    Having picked my towbar up on sunday. It looks fairly light duty. I'd defs want to look at reinforcing it to tow even a 205.
  13. Replies
    26
    Views
    1,106

    A few small jobs undertaken today. Replaced the...

    A few small jobs undertaken today. Replaced the feral auto T-bar.
    5336853369

    One of the big things that has annoyed me was the 2 different keys for doors and ign barrel. Had another slight score...
  14. Replies
    14
    Views
    331

    Thank you for the offers gents. I have found one...

    Thank you for the offers gents. I have found one in northern nsw. Cheers.
  15. Replies
    14
    Views
    331

    WTB: S1 405 sedan tow bar

    Hey all, finally realize the value of tow bars. Am after one for a 405 sedan.

    Cheers, James.
  16. Wiggling pins is normal, due to the size and...

    Wiggling pins is normal, due to the size and length of the ew10j4s pins. Just checked the spare head I have. 38T inlet. That's 9.5 deg every tooth. This is a high compression interference engine. If...
  17. Replies
    33
    Views
    1,067

    Haha...anyone remember wozza and the classified...

    Haha...anyone remember wozza and the classified ads? I sold one of them both my injected 504s for 2500 each circa 06. Tow truck picked them up, transported to melb to be cut in half and container'd...
  18. Its hard to say I didn't see how you did the...

    Its hard to say I didn't see how you did the belt, or turned the motor over. But to be honest when I saw your first thread about undoing the crank pulley without it being locked I was waiting for...
  19. You've possibly bent valves by undoing the crank...

    You've possibly bent valves by undoing the crank pulley bolt without it being locked. You've defs bent valves by turning the crank 180 to the cams. You can also peg the exhaust cam in the incorrect...
  20. Replies
    26
    Views
    1,106

    Possibly but the mi16 makes its max torque at...

    Possibly but the mi16 makes its max torque at 5000rpm. I'm not sure what an j4z torque is, but an j4 is 180nm right. An xu10j2, which this trans is fitted to develops 170nm at 2600. I think it...
  21. Replies
    26
    Views
    1,106

    Peter, I wouldn't look to much into it as every...

    Peter, I wouldn't look to much into it as every motronic diagram I have seen has an automatic output regardless of trans fitted. I wouldn't be surprised if a test car was built though.
  22. Replies
    2
    Views
    132

    Only need to do an abs bleed when replacing a abs...

    Only need to do an abs bleed when replacing a abs unit, even then you don't really have to..can do it on a test drive. Bleed the brakes like any other car. Clutch will be unaffected. It takes its...
  23. Replies
    26
    Views
    1,106

    This was literally the first 9 words of my post....

    This was literally the first 9 words of my post.



    Does the auto suit?...Hmm, look I've been after an automatic vehicle for a long time. With my job at the end of the day I'm exhausted and I...
  24. Replies
    26
    Views
    1,106

    Been playing with throttle/kickdown cable...

    Been playing with throttle/kickdown cable adjustments. Have the Auto shifting perfect, can't even notice the upshifts. With the 205/40/r17 tyres it sits at 100 effortlessly. 2300rpm @100kmh in an...
  25. Replies
    26
    Views
    1,106

    Had a really shabby set of brembo callipers that...

    Had a really shabby set of brembo callipers that I had been trying to sell for ages. Only wanted $200 for them IIRC, but because they were really shabby looking there was no takers. I decided to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Made by Cloudoru