Search Results - aussiefrogs - The Australian French Car Forum Since 1999
  • Register
  • Help

Search:

Type: Posts; User: Wintermute; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.20 seconds.

  1. Replies
    738
    Views
    76,410

    Oh it's that day again!! thanks for the tip!! ...

    Oh it's that day again!! thanks for the tip!!

    Tony.
  2. Replies
    738
    Views
    76,410

    Missed another one!! Perhaps next month :)

    Missed another one!! Perhaps next month :)
  3. The original manifold uses a long branch for revs...

    The original manifold uses a long branch for revs under 4000RPM, this increases the low end torque. The RS also has a different head and exhaust manifold, so you may find that this is just the...
  4. Replies
    10
    Views
    1,840

    I had the same problem many years ago. It was...

    I had the same problem many years ago. It was the zenner (fails short circuit and is wired (reverse) from positive to negative. As mentioned it protects against voltage spikes.

    The original is...
  5. Replies
    2,398
    Views
    298,920

    This morning turning onto Hill road off Paramatta...

    This morning turning onto Hill road off Paramatta rd. A red Peugeot 3008 Police car! It had some stylized word on the drivers door as well which I didn't catch. It appeared to have highway patrol...
  6. Replies
    38
    Views
    5,871

    Sticky: I wasn't able to attend either as I was attending...

    I wasn't able to attend either as I was attending a 90th Birthday party. I drove over the Silverwater bridge a bit before 11:00AM and it looked like it was a good turn out!

    Tony.
  7. Replies
    738
    Views
    76,410

    Sorry I should have posted that I was going to...

    Sorry I should have posted that I was going to come. Got the message at 10:00AM that the washer was ready to pick up and thought It'd only take me an hour and I'd be there by 11:00AM. based on the...
  8. Replies
    738
    Views
    76,410

    I suspect no one else will be arriving so I'll...

    I suspect no one else will be arriving so I'll head home.
  9. Replies
    738
    Views
    76,410

    Bugger just missed you. If i didn't stop for...

    Bugger just missed you. If i didn't stop for petrol would have caught you.

    Went to bankstown to pick up a pressure washer. On special at super cheap this weekend.

    Tony.
  10. Replies
    738
    Views
    76,410

    Thanks KB :)

    Thanks KB :)
  11. Replies
    738
    Views
    76,410

    No Notice this month? is Bigrr ok? Assuming...

    No Notice this month? is Bigrr ok? Assuming tomorrow is the day, though I am uncertain I will be able to attend, as the wife mentioned possibly doing something Sunday.

    Tony.
  12. Replies
    738
    Views
    76,410

    We were. I left around 1:00PM I think... ...

    We were. I left around 1:00PM I think...

    Some pics :)
  13. Replies
    738
    Views
    76,410

    I remembered at about 1:30PM, by which time I had...

    I remembered at about 1:30PM, by which time I had other things I had to do. Looks like I missed a good day!

    Tony.
  14. Replies
    22
    Views
    903

    I got mine when the airbox got wrecked hitting a...

    I got mine when the airbox got wrecked hitting a tall curb on Mt Victoria (diesel spill on the road)... 12 week wait for the new airbox, so got the pod as a temp fix.... I never put the new airbox...
  15. Replies
    22
    Views
    903

    No probs. WIll be interested to see what you...

    No probs. WIll be interested to see what you come up with :)

    Its been something I've thought about but not done anything (except the original buscuit tin).

    Tony.
  16. Replies
    4
    Views
    443

    Ah that's right. It is in a pig of a place. ...

    Ah that's right. It is in a pig of a place. Not easy to get to at all. Horrible job replacing it. I think I had blocked that memory out!

    Tony.
  17. Replies
    4
    Views
    443

    Sorry dup.

    Sorry dup.
  18. Replies
    4
    Views
    443

    yikes!! That plastic bit is pretty hefty, Have...

    yikes!! That plastic bit is pretty hefty, Have you lost the heat shield off the manifold? I'm trying to remember exactly what the plastic bung looks like, I think from memory it has a skirt...
  19. Replies
    22
    Views
    903

    I don't think I have any other pictures, but...

    I don't think I have any other pictures, but pretty sure that the piping is in two pieces. I only used the top half which connects to the intake scoop. I then ran the flexible hose from the bottom...
  20. Replies
    22
    Views
    903

    I don't think I have any other pictures, but...

    I don't think I have any other pictures, but pretty sure that the piping is in two pieces. I only used the top half which connects to the intake scoop. I then ran the flexible hose from the bottom...
  21. Replies
    22
    Views
    903

    I just checked the gallery and I found I had a...

    I just checked the gallery and I found I had a picture of the biscuit tin :) It is long gone but I used to be able to put the lid back on if I needed to, but generally ran it without.

    I think...
  22. Replies
    22
    Views
    903

    Yes it will hang down basically where the airbox...

    Yes it will hang down basically where the airbox is. It does pic up hot air when the car is stationary, the other thing you have to be careful about is going through water.

    I had a plastic...
  23. Replies
    20
    Views
    964

    If it is the cam cover seals you may find it runs...

    If it is the cam cover seals you may find it runs down the back of the engine and doesn't drip off, but gets blown off at speed, check the underside of the car, if there is greasy muck all the way...
  24. Replies
    21
    Views
    1,328

    maybe I should have said wear point rather than...

    maybe I should have said wear point rather than weak point... He said that over time because the brass was soft the teeth either wore or deformed (can't remember which). But that was a long time ago...
  25. Replies
    21
    Views
    1,328

    maybe I should have said wear point rather than...

    maybe I should have said wear point rather than weak point... He said that over time because the brass was soft the teeth either wore or deformed (can't remember which). But that was a long time ago...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4