View Profile: ReidarUF - aussiefrogs - The Australian French Car Forum Since 1999
  • Register
  • Help
Tab Content
  • ReidarUF's Avatar
    29th April 2019, 02:07 AM
    A few days ago I missed the oportunity to buy a R10 with a box like this(no fancy mecaparts parts) and a R5A engine. According to the owner it was...
    4 replies | 307 view(s)
No More Results

1 Visitor Messages

  1. View Conversation
    Hei! Fant en gammel tråd på trim-4-eldre forumet der du søkte etter 9mm kobberskiver. Fant du 9mm skiver og skiver til bremseslanger? Driver med akkurat samme jobben nå. Mvh Olav Helge
Showing Visitor Messages 1 to 1 of 1
About ReidarUF

Basic Information

About ReidarUF
Location:
Norway

Statistics


Total Posts
Total Posts
60
Posts Per Day
0.02
Last Post
Renault R5 5-speed box in R8/R10 29th April 2019 02:07 AM
Visitor Messages
Total Messages
1
Most Recent Message
8th March 2019 09:06 AM
General Information
Last Activity
17th May 2019 12:16 AM
Join Date
5th November 2011
Referrals
0

28 Likes

LastPage 1 of 2 12 Last
  1. ReidarUF
    ReidarUF liked post by Frans On thread : Renault R5 5-speed box in R8/R10
    Hi All, I have taken the opportunity to make a new dedicated thread that could assist in future searches on this subject. Frans. This is a direct copy of what Carvel sent me. The rationale...
    Liked On: 29th April 2019, 01:58 AM
  2. ReidarUF
    ReidarUF liked post by Stuey On thread : Brake caliper piston - Renault R8 Gordini
    I'm late to this party, but I remembered I'd read ages ago that square section seals also have the benefit of causing a slight retraction of the piston too, by flexing and returning (as in the...
    Liked On: 25th April 2019, 10:34 AM
  3. ReidarUF
    ReidarUF liked post by Frans On thread : A very desirable collection.
    Hi Col, I'll paste some more for you but I'm sure some of them have been up here so there might be duplicates. He's got too many to keep track. http://i65.tinypic.com/hwycuo.jpg ...
    Liked On: 13th April 2019, 05:43 AM
  4. ReidarUF
    ReidarUF liked post by Frans On thread : A very desirable collection.
    Hi, My mate Jimmy from ZA where asked if some of his cars can be displayed at a new dealer that has opened somewhere in Johannesburg. Here are the photos of them loading some of his cars on a...
    Liked On: 12th April 2019, 10:17 AM
  5. ReidarUF
    ReidarUF liked post by Frans On thread : R8/R10 Master Cylinder change.
    That's nothing :jiggy: Installing 2 master cylinders with a balance bar in a front radiator car (race car) without a hoist as well.
    Liked On: 25th March 2019, 02:28 AM
  6. ReidarUF
    ReidarUF liked post by Bustamif On thread : R8/R10 Master Cylinder change.
    Changing a tandem master cylinder with the front radiator hoses restricting access even more, still without a hoist. All character building stuff, just suck it up and get-r-done !
    Liked On: 25th March 2019, 02:27 AM
  7. ReidarUF
    ReidarUF liked post by jaahn On thread : 336 Bellhousing
    Hi R8RX :) Perhaps you did not understand Alan Moore when he said he changed the operation of his cable to use the inner cable as the fixed part and the outer sleeve then moved the correct way to...
    Liked On: 20th March 2019, 12:01 PM
  8. ReidarUF
    ReidarUF liked post by Frans On thread : Brake caliper piston - Renault R8 Gordini
    I'm not sure about the following idea in my head. I have always thought that the casting indent on the front of the caliper tells you what seal to use, square or round. Then on the other hand I can't...
    Liked On: 19th February 2019, 04:42 PM
  9. ReidarUF
    ReidarUF liked post by Frans On thread : Brake caliper piston - Renault R8 Gordini
    Hi Reidar, No the adjuster mechanism is actually there to keep the pads close to the rotors. As the pads wear down the hydraulic pressure will force the piston out of the adjusting mechanism...
    Liked On: 14th February 2019, 08:24 AM
  10. ReidarUF
    ReidarUF liked post by geckoeng On thread : Brake caliper piston - Renault R8 Gordini
    R8RX, You need the old adjuster slides, that come out of your current calipers. Check the size of the locking thread as some are M8 and some M9. The split in the slide ring needs to be inserted in...
    Liked On: 14th February 2019, 05:12 AM
  11. ReidarUF
    ReidarUF liked post by Frans On thread : Gordini and Matra outing
    Hi All, About 2 months ago me and my son got an invitation from a photographer to do a photo shoot with the 2 cars for a Classic Car Calendar. We made an appointment and met him at a spot and from...
    Liked On: 19th November 2018, 03:41 PM
  12. ReidarUF
    ReidarUF liked post by rosbosca On thread : R1135 steering wheel
    Hi everyone, Looks like I have come up with a method of repairing the wheel. Won't know until I get it back in a month or so. Will keep you posted. Ross
    Liked On: 6th November 2018, 04:29 AM
  13. ReidarUF
    ReidarUF liked post by Frans On thread : Enduro Renault Supreme.
    Hi All, When I bought the 21 Turbo, I joined a British Forum and through them I met Jeff, a long time 21 Turbo owner. During a visit one evening he showed me the car and told me the story behind...
    Liked On: 16th September 2018, 11:48 AM
  14. ReidarUF
    ReidarUF liked post by Frans On thread : Two new racecars in NZ
    Hi All, Hi ReidarUF, I know the gauges you are talking about. We have used it in the industry and they are actually filled with Glyserine. The Bourdon tube, that is driving the needle, and the...
    Liked On: 3rd September 2018, 07:11 PM
  15. ReidarUF
    ReidarUF liked post by Frans On thread : Forgive me for I have sinned.
    Hi All, Yes, I have done the deal and I must admit that I had hundreds of valid reasons why I had to do this! The one reason is more valid than the previous one. I'm sure that you will...
    Liked On: 27th July 2018, 11:54 AM
LastPage 1 of 2 12 Last