View Profile: brettr - aussiefrogs - The Australian French Car Forum Since 1999
  • Register
  • Help
Tab Content
  • brettr's Avatar
    21st February 2017, 10:52 PM
    A patent would imply a working design and is only necessary if someone else wants what you've done. I have neither currently. So the only thing I...
    551 replies | 59772 view(s)
  • brettr's Avatar
    21st February 2017, 03:22 PM
    Been developing more sub systems..... Sent from my E5823 using Tapatalk
    551 replies | 59772 view(s)
  • brettr's Avatar
    15th February 2017, 06:15 AM
    Hey 21571, I'm the furthest thing from an expert available. It's hard to say as its not a switch. But 80 I would like to see it opening. Too...
    551 replies | 59772 view(s)
  • brettr's Avatar
    13th February 2017, 11:29 PM
    Sequencing done. It's running on the Ca18det tune that was last in the ecu from the last engine. So had to stuff around wiring the alternator. It...
    551 replies | 59772 view(s)
  • brettr's Avatar
    12th February 2017, 10:43 PM
    Yep, was a hot couple of days Chris. And the shed inside feels like it was 50 but the thermometer only was showed 46 so that was ok. Just made a...
    551 replies | 59772 view(s)
  • brettr's Avatar
    10th February 2017, 09:07 PM
    Not much time tonight so just connected up fuel lines to the carbs. Planning on a big weekend to get it going while I'm on the rotisserie in...
    551 replies | 59772 view(s)
  • brettr's Avatar
    9th February 2017, 09:03 PM
    Just looking at water pipe routing and rewiring some loom segments to be fit neater etc. Did start on the catch can setup too. Sent from...
    551 replies | 59772 view(s)
  • brettr's Avatar
    8th February 2017, 11:16 PM
    Hey guys I'm just back from the workshop, just been making some clutch release bits. I did actually give it a little turn, I was convinced with...
    551 replies | 59772 view(s)
  • brettr's Avatar
    7th February 2017, 06:15 PM
    Hi 21571, Yes it does, I take the main two engine lines off at the remote block and prime all open ports, so to cooler core, back to oil pump and...
    551 replies | 59772 view(s)
  • brettr's Avatar
    6th February 2017, 11:28 PM
    Not much tonight, just filled it with oil, then used my patented oil primer method which is a boat fuel bulb and lines. Works really well, you...
    551 replies | 59772 view(s)
  • brettr's Avatar
    5th February 2017, 09:42 PM
    Yep was hot. 10 hours went quick with not a lot to show. Put the plugs in and then made a plate to cover the mech fuel pump. Then made a...
    551 replies | 59772 view(s)
  • brettr's Avatar
    4th February 2017, 08:45 PM
    So the CAS. As said it's sealed and non serviceable. But if you want to do this drill the screws out and knock the guts out. Pull the...
    551 replies | 59772 view(s)
  • brettr's Avatar
    3rd February 2017, 08:29 PM
    Take an old Ca18det ignition daughter harness and cut and shut. Rewire it to use Toyota echo cop plugs. Then rewrap with vulcanising tape....
    551 replies | 59772 view(s)
  • brettr's Avatar
    2nd February 2017, 10:49 PM
    So worked on stuff that I had been putting off. First I had no memory of doing up the oil gallery plug behind the supercharger bracket so pulled...
    551 replies | 59772 view(s)
  • brettr's Avatar
    1st February 2017, 08:21 PM
    Made the coupler for the distributor but then realised that the Nissan cas is driven directly off the exhaust cam. That means it rotates clockwise...
    551 replies | 59772 view(s)
  • brettr's Avatar
    30th January 2017, 10:47 PM
    I've actually ordered a new 1.25kw starter from France. And jman the header is coming, just put this on temporary while I'm waiting for the laser...
    551 replies | 59772 view(s)
  • brettr's Avatar
    29th January 2017, 10:33 PM
    Hey guys, I'm not planning any meth or water. Will run a det sensor and the ecu runs the det map on detonation. I don't think with...
    551 replies | 59772 view(s)
  • brettr's Avatar
    28th January 2017, 10:44 PM
    Yep the wrinkle was easy, just getting it real thick without a run is the trick, I reckon this will need a week to really go off, it was ultra thick....
    551 replies | 59772 view(s)
  • brettr's Avatar
    28th January 2017, 07:49 PM
    Thanks jman, and yes Kevin it moves all the time. Spose I'm just never content. And Rob, don't know what boost it will push. Main pulley is 150...
    551 replies | 59772 view(s)
  • brettr's Avatar
    26th January 2017, 06:13 PM
    Carb bodies on and plenum. Injectors in. Off the engine stand and flywheel on with new bolts and centre clutch.
    551 replies | 59772 view(s)
  • brettr's Avatar
    25th January 2017, 08:36 PM
    Next stage is a 75hp nitrous shot. They are all valid points, I will be amazed though if the crank snout comes off. Check out this ford 351...
    551 replies | 59772 view(s)
No More Results
About brettr

Basic Information

About brettr
Location:
sydney

Signature


BR

Building a race car is easy - building a race car that can be road registered is hard.

For any custom fabrication call Precision One Off Engineering - Sydney 02 4587 8666

Statistics


Total Posts
Total Posts
370
Posts Per Day
0.16
Last Post
R8 upgrade project 21st February 2017 10:52 PM
General Information
Last Activity
Yesterday 04:18 PM
Join Date
3rd November 2010
Referrals
0