View Profile: alittlewino - aussiefrogs - The Australian French Car Forum Since 1999
  • Register
  • Help
Tab Content
  • alittlewino's Avatar
    29th April 2017, 09:20 AM
    purchased a newbie from Spareto for our 306 - even with express 3 day delivery cost it was half price compared to local - and they have a wide range
    5 replies | 212 view(s)
  • alittlewino's Avatar
    26th April 2017, 12:05 AM
    alittlewino replied to a thread 306 just stopped in Peugeot Forum
    funny thing, my metal cup actually had some of the plastic of the housing tube broken off inside it only noticed when I was having a little play ...
    38 replies | 1245 view(s)
  • alittlewino's Avatar
    25th April 2017, 04:34 PM
    alittlewino replied to a thread 306 just stopped in Peugeot Forum
    my grommet is also quite messy and difficult to photo - it had actually split and I super-glued it back together it's also flattened at one end I...
    38 replies | 1245 view(s)
  • alittlewino's Avatar
    22nd April 2017, 06:50 AM
    alittlewino replied to a thread 306 just stopped in Peugeot Forum
    The off-idle flat spot on depressing the accelerator is a very good tell-tale for low fuel pressure and should immediately alert one to this...
    38 replies | 1245 view(s)
  • alittlewino's Avatar
    21st April 2017, 07:45 AM
    alittlewino replied to a thread 306 just stopped in Peugeot Forum
    That is awesome - if I had the time I would have also tried a seal maker but well done to you for sorting. Did you also look at that odd black...
    38 replies | 1245 view(s)
  • alittlewino's Avatar
    17th April 2017, 10:20 PM
    alittlewino replied to a thread 306 just stopped in Peugeot Forum
    I searched far and wide for the seal including Europe without success suspect one would need to find the pump manufacturer to source I hope you...
    38 replies | 1245 view(s)
  • alittlewino's Avatar
    17th April 2017, 01:44 PM
    thank you - corrosion sounds like it as the drip is consistent with a very very tiny hole - frightened to touch anything on this 16yr old car as it...
    4 replies | 96 view(s)
  • alittlewino's Avatar
    17th April 2017, 11:49 AM
    have an odd drip where the top water hose slots into the thermostat cover I literally touched the hose while doing the crank position sensor and...
    4 replies | 96 view(s)
  • alittlewino's Avatar
    16th April 2017, 09:53 PM
    alittlewino replied to a thread 306 just stopped in Peugeot Forum
    I was also apprehensive but it unclips ok just looks more fragile. My issue was the small internal seal that the pump outlet pipe pokes into inside...
    38 replies | 1245 view(s)
  • alittlewino's Avatar
    13th April 2017, 07:09 AM
    f/s bare pump itself, not the cannister body etc. have this on evilbay but prefer to sell personally FUEL PUMP FOR PEUGEOT 306 406 1.4 1.6 1.8 2.0...
    0 replies | 86 view(s)
  • alittlewino's Avatar
    10th April 2017, 02:41 PM
    alittlewino replied to a thread 306 just stopped in Peugeot Forum
    to update - we have decided to keep the car longer term so bit the bullet and replaced Idle stepper motor, MAP, Crank, Throttle, Temp and O2 sensors,...
    38 replies | 1245 view(s)
No More Results
About alittlewino

Basic Information

About alittlewino
Location:
Brisbane

Statistics


Total Posts
Total Posts
86
Posts Per Day
0.05
Last Post
407 3.0 v6 sanden air compressor 29th April 2017 09:20 AM
General Information
Last Activity
29th April 2017 09:20 AM
Join Date
1st May 2012
Referrals
0